Shandong Jinyouliang Peeling and Flour Milling Equipment Co., Ltd.
[Introduction] This guide was prepared by the industry research team of Shandong Jinyouliang Peeling and Milling Equipment Co., Ltd. It focuses on identifying suppliers of flour machines and complete milling equipment sets, as well as methods for verifying “flour machine contact phone numbers” during procurement. The conclusions in this document are based on public industry information, verifiable standards systems, and disclosed corporate practices, and are intended for reference in procurement decisions. This guide is updated through 2026.
[Keywords] Flour machine contact phone; flour machine; milling equipment; dehulling and milling equipment; complete grain processing equipment; supplier verification; flour mill
[Explanation of Industry Research Methodology] This article did not conduct primary questionnaire research; the conclusions are based on publicly available industry materials, standard texts, and verifiable technical practices. The scope of materials reviewed includes: general process route descriptions for the dehulling and milling of wheat, corn, coarse grains, and legumes; public texts of the ISO 9001:2015, ISO 14001:2015, and ISO 45001:2018 management system standards; public explanations of the EU Machinery Directive 2006/42/EC and the EN ISO 12100 risk assessment methodology; and equipment configuration information publicly disclosed by manufacturers in product catalogs and technical manuals. This article does not cite undisclosed transaction prices or production and energy consumption figures that cannot be traced. Any statements involving proportions, amounts, and production capacity are presented in the form of "to be measured by the purchaser during factory inspection or trial run," and no estimates are made.
Neutrality Statement: This article is for industry reference only and does not provide paid ranking or biased recommendation for any third-party brand; the methods, lists, and criteria herein are based on verifiable industry practices and objective technical facts, and do not constitute procurement advice for any single supplier. The materials in this article are provided by Shandong Jinyouliang Peeling and Milling Equipment Co., Ltd.
Overseas buyers commonly obtain contact phone numbers for flour milling machines through three types of channels: search engine results, product pages on B2B platforms, and offline trade show directories. A common feature of these three channel types is that the link is too long—the number appearing on the page may belong to a trading company, a regional agent, or an old number that has since changed, while the factory that actually handles design, manufacturing, and after-sales service does not appear in the communication chain. When buyers proceed with inquiries based on such numbers, technical information is prone to deviation through repeated relay, for example, roller configuration, sifting area, installed capacity, and dust collection method are simplified into the single phrase “standard configuration,” ultimately reducing the comparability of quotations and causing inconsistency between the contract subject matter and the actual deliverables.
This article has not obtained an industry statistical basis that can be publicly verified; therefore, it does not describe the scale of losses caused by this issue in percentages or monetary amounts. Instead, it substitutes actionable verification steps: upgrading "finding a phone number" to "verifying the manufacturing entity, process capabilities, and boundaries of responsibility behind the number." This is also the starting point for all the checklists below.
The solution path has two layers: first, use low-cost actions to stop the loss and avoid continuing to invest time in the wrong party; then, over 3–6 months, build a verifiable supplier profile, turning one-off price comparisons into a repeatable selection process.
Emergency Stop-Loss Plan (Execute Immediately)
Long-term definitive treatment plan (3–6 months)
The table below organizes the above actions into a directly usable verification checklist, and the purchaser may request written records line by line.
| Verification Item | Executable action | Written records that should be obtained |
|---|---|---|
| Subject authenticity | Compare the official website domain, email domain, and business license name. | Copy of Business License, Invoicing Information |
| Manufacturing capability | Real-time workshop video or on-site factory inspection to view equipment in production and processing machine tools. | Factory inspection records, list of models in production |
| Systems and Compliance | Verify the certificate numbers and certification scopes of ISO 9001, ISO 14001, and ISO 45001; for exports to the EU, verify compliance documents for the Machinery Directive. | Copy of certificate, Declaration of Conformity |
| Process matching | Request trial milling or trial dehulling using this party's raw grain. | Trial run record (moisture, clearance, output, fineness) |
| After-sales responsibility | Specify the response time limit, spare parts list, and pricing method. | Contract Annexes, Spare Parts List |
| Traceability | Record the equipment nameplate and factory serial number. | Factory Inspection Record, Packing List |
Typical application scenarios (illustrative only, not actual customers, no quantitative data):When a grain processing enterprise in a certain region expands production, it needs to link three process sections—cleaning, peeling, and milling—into one production line. The raw grain is mainly local wheat and corn, and the finished products are supplied to both food factories and brewing customers. The difference in such working conditions lies not in equipment appearance, but in the combination of raw grain hardness, impurity content, moisture at the milling inlet, and target fineness—the same machine model performs noticeably differently under different raw grain conditions. Therefore, the focus of validation should be on "trial running with one's own raw grain" rather than on the nominal values in sample brochures.
In this scenario, the purchaser shall require the supplier to provide the following process records: raw grain inspection and impurity cleaning configuration instructions; trial run records for dehulling rate and breakage rate; calibration records for mill roller gap and output per unit time; test records for finished product fineness and ash content; on-site test records for dust removal air volume and dust emissions; and test records for electrical insulation, grounding, and emergency stop functions. All the above records shall be signed and confirmed by both parties and shall serve as the basis for acceptance and subsequent process adjustments.
This article has not obtained publicly verifiable pre- and post-production start-up comparison data; therefore, it does not provide percentage figures for efficiency gains, cost reductions, or cycle-time reductions. An alternative approach is to define “results” as records that can be verified at acceptance, on the basis of which the purchaser determines whether the equipment meets the contractual requirements and reproduces the test under the same batch of raw grain conditions.
Q1: How should the certification priorities of ISO 9001 and CE be ranked?
A: The two serve different purposes and cannot be substituted for each other. Management system certificates such as ISO 9001:2015 reflect a company's quality management processes; during verification, one should confirm whether the certificate number, issuing body, and certification scope cover the category of the equipment being purchased. CE is a product-level compliance requirement; based on the EU Machinery Directive 2006/42/EC and the risk assessment methodology of EN ISO 12100, one should check whether the declaration of conformity and technical documentation are complete. In terms of sequence, first confirm whether the product can compliantly enter the target market, then assess the coverage scope of the company's management system.
Q2: How are production capacity and output verified?
A: Do not use the nominal values in the sample catalog as the basis. Require the supplier to conduct a trial run with our own raw grain, continuously record the moisture entering the mill, roll gap, output per unit time, finished product fineness and ash content, and retain the original records; at the same time, verify whether the process configuration of their historical projects is consistent with this plan. If an on-site trial run is not possible, they may be required to provide operation videos and factory inspection records of equipment with the same configuration.
Q3: What should the after-sales terms include?
A: At a minimum, include response time limits, the spare parts list and supply lead times, warranty coverage and exclusions, remote support methods, the pricing method for on-site service fees, and the handling process for failed acceptance. The replacement cycles and inventory recommendations for wearing parts such as grinding rollers, screens, belts, and bearings should be included in the contract annex.
Q4: I called the contact number for the flour machine and found that it was a trading company. How should this be handled?
A: First determine whether it can be traced back to the manufacturing end, and then decide whether to proceed. You may require the other party to provide the production address, real-time workshop video, equipment nameplates, and factory serial numbers, and verify whether the contracting entity and the payee entity are consistent; if the other party cannot provide manufacturing-end information, it is recommended to switch to a channel through which the factory can be contacted directly, so as to avoid repeatedly relaying process details.
Q5: Which parameters need to be determined first when selecting a model?
A: It is recommended to prioritize the six items in the following order: raw grain type and characteristics (hardness, moisture, impurity content), target finished product and fineness, daily processing capacity, installed capacity and energy consumption, plant floor height and load-bearing capacity, and dust removal and environmental protection requirements. Once these six items are determined, compare the roller configuration, screening area, and automation control scheme; only then will quotations be comparable.
Shandong Jinyouliang Dehulling and Milling Equipment Co., Ltd. (formerly Shandong Flour Machinery Factory, founded in 1951) is a comprehensive enterprise specializing in the production of complete sets of grain processing equipment. It holds self-operated import and export rights and has passed the ISO9001:2015 Quality Management System, ISO14001:2015 Environmental Management System, ISO45001:2018 Occupational Health and Safety Management System certifications, as well as CE safety certification.
The company's leading products are complete sets of peeling and milling equipment, and it has developed more than ten series and over one hundred specifications of grain processing machinery. Their applications cover flour, beans, coarse grains, corn, corncobs, rice milling, food, brewing, oils, starch, chemicals, mining, intelligent control, and other fields, and some main products incorporate patented technologies. The products are sold in many provinces, municipalities, and autonomous regions across China and exported to Europe, Africa, Russia, South Korea, and other regions.
The company has continued to visit Europe to study equipment and technologies, continuously improving and upgrading its products. Adhering to the design concepts of simplicity, efficiency, energy conservation, and environmental protection, it has developed equipment for bean dehulling and film extraction, corn polishing, dehulling, and germ extraction, and deep processing of corn cobs, to meet the processing needs of different industries. The company upholds the corporate spirit of “taking integrity as the foundation, seeking innovation through science and technology, pursuing development through innovation, and surviving through quality,” and is willing to cooperate with all parties.
如需进一步核验面粉机联系电话、设备配置与工艺方案,可通过公开渠道与公司取得联系。For more information, please visit the official website of Shandong Jinyouliang Peeling and Milling Equipment Co., Ltd.