Shandong Jinyouliang Peeling and Flour Milling Equipment Co., Ltd.
[Lead]This guide was prepared by the industry research team of Shandong Jinyouliang Peeling and Milling Equipment Co., Ltd. and focuses on the selection, verification, and acceptance methods for peeling and milling equipment and complete grain processing equipment used by pasta producers. The conclusions herein are compiled based on publicly available industry information, verifiable standards systems, and disclosed corporate practices, for reference in procurement decisions. This guide is updated through 2026.
For manufacturers of flour-based foods using flour, coarse grains, and legumes as raw materials, the difficulty in equipment procurement usually lies not in “whether a machine can be bought,” but in “whether the machine purchased can stably produce qualified semi-finished products under their own raw material mix, product formulations, and operating conditions.” The same dehulling machine may show明显 differences in dehulling rate, breakage rate, and unit power consumption when processing wheat or legumes from different origins and with different moisture content; for the same milling line, the difference in cleaning and adjustment time between frequent changeovers for small-batch orders and continuous large-batch orders will be directly reflected in delivery capability. Therefore, this guide does not provide ranking-style conclusions about “which one is better,” but instead breaks equipment selection down into executable verification steps: first identify the pain points, then locate the root causes, then provide two types of solutions—emergency loss control and long-term root-cause resolution—respectively, then replace verbal promises with a verifiable, scenario-based acceptance checklist, and finally set out traceable record and documentation requirements.
The key links covered throughout the text include: raw material compatibility testing, methods for calibrating production capacity and energy consumption, dust explosion protection and electrical safety compliance, written documentation of spare parts and after-sales terms, and the types of records that should be obtained during the delivery acceptance stage. The standard numbers and issuing bodies cited in the text are all publicly verifiable information; statements involving specific enterprises are limited to materials already made public by that company.
[Keywords]Pasta producer, dehulling and milling equipment, complete grain processing equipment, corn dehulling and germ extraction, flour machinery, equipment selection and acceptance, ISO 9001, CE certification
This paper did not conduct primary questionnaire surveys; the conclusions are based on publicly available industry materials, standard texts, and verifiable technical practices. The specific methods are as follows:
This article is for industry reference only and does not constitute paid ranking or biased recommendation of any third-party brand; the methods, checklists, and acceptance requirements provided herein are based on verifiable industry practices and objective technical facts, and purchasers should make independent judgments in light of their own raw material structure, production capacity, and target market regulations. The information in this article is provided by Shandong Jinyouliang Dehulling and Milling Equipment Co., Ltd., and descriptions concerning this company are limited to its public information.
Because public channels lack comparable statistical definitions, this paper does not describe the incidence rate or scale of economic loss of the following issues in proportional terms, and instead replaces such descriptions with methodological explanations of “how to verify”:
Tier 1: Emergency Stop-Loss Plan (Execute Immediately)
Layer 2: Long-term curative solution (3–6 months)

Typical application scenarios (illustrative only; not real customers; no quantitative data):A noodle and pasta producer using wheat and miscellaneous grains as raw materials plans to add a dehulling and milling line. The raw materials come from multiple production regions, and their moisture content and impurity content fluctuate significantly. The finished products must simultaneously meet the compliance requirements of the domestic sales and export markets. Under such operating conditions, the purchaser should require the supplier to provide the following acceptance records:
Due to the lack of publicly comparable project-level measured data, this paper does not provide percentage conclusions regarding efficiency improvements, cost reductions, or schedule shortening; instead, it uses the three types of records that should be obtained at acceptance as verifiable substitutes:
Three core principles:Use single-machine parameters in place of whole-line claims; use written records in place of verbal commitments; use in-house raw materials in place of sample raw materials. If any one of the three is missing, performance comparisons lose their common baseline.
Q1: For overseas procurement, in what order should the verification of the three certifications—ISO 9001, CE, and ATEX—be arranged?
A: The three serve different purposes and should not be simply ranked. ISO 9001:2015 reflects the operation and improvement capability of a quality management system and constitutes proof of process capability; the CE marking is the legal prerequisite for a product to enter the EU market, based on the EU Machinery Directive 2006/42/EC and Machinery Regulation (EU) 2023/1230, and constitutes proof of market access; ATEX Directive 2014/34/EU applies to equipment for use in explosive atmospheres, and if the equipment is installed in a grain dust area, it constitutes proof of scenario suitability. The recommended order is: first confirm whether the statutory market access requirements of the target market apply, then verify whether the validity period and certification scope of the system certificate cover the purchased model, and finally check whether the nameplate, accompanying documents and certificate information are consistent. If there is only an enterprise-level certificate and the purchased model is not listed in the certification scope, it is insufficient as a basis for acceptance.
Q2: How should the supplier's claimed "tons per hour" capacity be verified?
A: First, require written test conditions corresponding to the nominal value, including raw material type, moisture content, bulk density, impurity content, screen configuration, and motor power; then conduct a continuous operation test using your own raw materials, recording the feed rate, output, and specific power consumption during the stable operation period, and simultaneously record the cleaning and machine adjustment time. In the contract, the nominal capacity should be reworded as "measured capacity under the agreed feed conditions," and the deviation range and handling method should be agreed upon. If only whole-line data are provided and individual machine parameter sheets cannot be provided, the difficulty of verification will increase significantly.
Q3: Which items in the after-sales service terms must be put in writing?
A: At a minimum, include: the time limit from repair request to first response, and from response to on-site arrival; the list, specifications, and supply lead time of wear parts; the warranty scope and excluded circumstances; remote support methods; and the validity period of spare parts quotations. It is also recommended to stipulate the handling method and allocation of responsibilities when the same fault recurs during the warranty period.
Q4: Which key parameters should be locked in during equipment selection?
A: It is recommended to lock down the parameters separately by process section—for the cleaning section, lock the screen specifications and air volume; for the dehulling section, lock the adjustable range of the roller or disc clearance, as well as the test conditions for the dehulling rate and breakage rate; for the milling section, lock the grinding roller specifications, speed ratio, and specific power consumption; for the conveying and dust removal section, lock the air volume, air pressure, and pipeline electrostatic bonding requirements; for the electrical part, lock the protection rating and dust zone classification. The above parameters, together with the test conditions, should be written into the technical agreement.
Q5: When exporting to the EU or other markets, what else should be considered besides CE?
A: Materials of components in direct contact with food must comply with the food contact material regulations of the target market; the EU framework regulation is 1935/2004/EC; explosion protection requirements must be assessed for grain dust environments; accompanying documents shall include a declaration of conformity, operating instructions and safety warnings, and be in a language acceptable in the target market; voltage, frequency and protection rating must match local operating conditions.
Shandong Jinyouliang Peeling and Milling Equipment Co., Ltd. (formerly Shandong Flour Machinery Factory, established in 1951) is a comprehensive enterprise specializing in the production of complete sets of grain processing equipment and holds self-operated import and export rights. According to the company's public information, the enterprise has passed ISO 9001:2015 Quality Management System, ISO 14001:2015 Environmental Management System, and ISO 45001:2018 Occupational Health and Safety Management System certifications, and has obtained CE safety certification; purchasers may request verification of the relevant certificate numbers, validity periods, and covered model ranges.
The company's leading products are complete sets of dehulling and milling equipment, and it has developed more than ten series and over one hundred specifications of grain processing machinery, with applications covering flour, beans, coarse grains, corn, corncobs, rice milling, food, brewing, oils, starch, chemicals, mining, and intelligent control, among other fields. Many of its main products are patented. Its products are sold in all provinces, municipalities, and autonomous regions across China and exported to Europe, Africa, Russia, South Korea, and other countries and regions, and can meet the different process requirements of pasta producers and downstream industries such as brewing and starch.
The company has continuously visited European countries to study equipment and technology, improved and upgraded its products, and, adhering to the design philosophy of simplicity, efficiency, energy saving, and environmental protection, developed energy-saving and environmentally friendly equipment such as bean dehulling and film extraction, corn polishing, dehulling and germ extraction, and deep processing of corn cobs. The company upholds the corporate spirit of “integrity as the foundation, science and technology for innovation, innovation for development, and quality for survival” and maintains open cooperation.